>
Subscribe Newsletter
*

*

pdf Custom 2K56  

 pdf Custom 2K95    

 pdf Custom 2K160  

 pdf Custom 2K240  

 pdf Custom 2K325  

 pdf Custom 2K444  

airpot_precision_dashpots CustomCustom

Airpot Precision Dashpots in custom configurations which offer a range of sizes and capabilities likely to satisfy many requirements in which accurate and repeatable control of force and or impact is desired.  Custom Airpot Dashpots have been catagorized in 6 bore diameters ranging from .22 inches to 1.75 inches with either push, pull, or two-way damping. Within specified limits you can obtain a specific stroke, mounting length, rod type and rod end design. Additional custom configurations are possible with Airpot engineering collaboration.

MODEL  2K56 -
Bore Size: .220" (5.59 mm)
 2K95 -
Bore Size: .366" (9.3 mm)
 2K160 - Bore Size: .627" (15.93 mm)  2K240 - Bore Size: .945" (24 mm)  2K325 - Bore Size: 1.281" (32.5 mm)  2K444 - Bore Size: 1.750" (44.4 mm)
 BORE (inches)  0.22  0.366  0.627   0.945  1.281  1.75
STROKE RANGE (inches) (any x.xxx) .125 - 11.0 .125 - 11.0 .125 - 13.0 .125 - 12.0 .125 - 10.0 .125 - 8.0
 FIXED STROKE FOR SNUBBER MODELS (inches)  N/A  N/A  1.5  2   2   2
 FORCE CAPACITY: PULL DAMPING DIRECTION lbs force (Starting from fully retracted position)  0.5  1.4  4  9  17  30
 FORCE CAPACITY: PUSH DAMPING DIRECTION lbs force (Starting from fully extended position)  0.35  1  3  7  13  24
 APPROX. ENERGY CAPACITY: PULL DAMPING DIRECTION FOR 1 IN. STROKE (inch-lbs)  0.22  0.64  1.8  4.1  7.5  14
APPROX. ENERGY CAPACITY: PULL DAMPING DIRECTION FOR 3 IN. STROKE (inch-lbs) 0.75 2.2 6.1 14 26 48
APPROX. ENERGY CAPACITY: PUSH DAMPING DIRECTION FOR 1 IN. STROKE (inch-lbs) 0.28 0.8 2.2 5.2 9.5 18
APPROX. ENERGY CAPACITY: PUSH DAMPING DIRECTION FOR 3 IN. STROKE (inch-lbs) 1.5 4.2 12 27 50 93
 APPROX. ENERGY CAPACITY: SNUBBER MODELS TO STANDARD STROKE (ft-lbs)  N/A  N/A  0-.3  0-.75  0-3  0-7
 DAMPING COEFICIENT RANGE: FORCE/VELOCITY: lbs/(in/sec)  0-.5  0-2  0-5  0-30  0-40  0-40
 FRICTION COEFFICIENT (approx.) Static and dynamic  0.2  0.2  0.2  0.2  0.2  0.2
 PISTON FRICTION WHEN HORIZONTAL (without side load):grams  <1  <1  <1  <1  <4  <8
 OPERATING TEMPERATURE RANGE *NOTE: If operating at temperatures over 70 degrees C (158 degrees F) please advise factory  -55C to +150C  -55C to +150C  -55C to +150C  -55C to +150C  -55C to +75C  -55C to +75C
COMPONENT WEIGHT: Fixed mass in grams (cylinder, bottom, etc.) =(C1 x Stroke) + C2 C1 = 1.2 C2 = 6.4  C1 = 2.9 C2 = 8.9  C1 = 6.1 C2 = 13.6  C1 = 11.5 C2 = 40.6  C1 = 17.5 C2 = 60.3  C1 = 25.7 C2 = 82.1
 COMPONENT WEIGHT: Movable mass in grams (piston and rod) =(C3 x Stroke) + C4  C3 = .2 C4 = 1.4  C3 = .4 C4 = 2.8  C3 = .4 C4 = 4.3  C3 = 1.3 C4 = 8.3  C3 = 6.3 C4 = 13.6  C3 = 6.3 C4 = 31.6
© Vivek Engineers. All Rights Reserved.